|
Properties |
Test Method |
Typical Value |
||
|
|
|
English |
SI |
|
|
Physical |
||||
|
Specific Gravity |
gr./cm3 |
ASTM D-792 |
1.25 |
1.25 |
|
Hardness |
Shore D |
ASTM D-2240 |
60D |
60D |
|
|
||||
|
Mechanical |
||||
|
Tensile Strength (Ultimate) |
psi/MPa |
ASTM D-412 |
6200 psi |
42.8 MPa |
|
Tensile Stress |
@100% Elong |
ASTM D-412 |
3200 psi |
22.1 MPa |
|
Tensile Stress |
@300% Elong |
ASTM D-412 |
5300 psi |
36.6 MPa |
|
Elongation at Break |
% |
ASTM D-412 |
450% |
450% |
|
Tensile Set at Break |
% |
ASTM D-412 |
110% |
110% |
|
Compression Set, % |
22 hrs@ 23ºC |
ASTM D-395 (B) |
40% |
40% |
|
Compression Set, % |
22 hrs@ 70ºC |
ASTM D-395 (B) |
50% |
50% |
|
Tear Strength |
lb./in. N/mm |
ASTM D-624, Die C |
1150 lb./in. |
202 N/mm |
|
Taber Abrasion Resistance / mg loss |
1000 gr./H-18 |
ASTM D-1044 |
50 mg |
50 mg |
|
|
||||
|
Thermal |
||||
|
Vicat Softening Point |
|
ASTM D-1525 |
295°F |
145°C |
|
Glass Transition Temperature |
|
DSC |
30oF |
0oC |
|
|
|
|
|
|
|
Processing Conditions, Inj. Molding |
|
|
400 - 440oF |
205 - 225oC |
echnical Bulletin Polyester Type
Elastollan S60D53N is a polyester-based thermoplastic polyurethane (TPU). It exhibits excellent abrasion resistance and toughness, good heat, oil, fuel, and solvent resistance. As with all TPU products, Elastollan S60D53N must be dried before processing. The drying step is required to maintain a low moisture content until the product enters the processing equipment. The water content must be less than 0.03% before and during
processing. The typical drying conditions should be 2-4 hours @ 195º-220ºF (90º-105ºC). Elastollan S60D53N can be stored for up to 1 year in its original container. Containers should be stored in a cool and dry area.
The above values are shown as typical values and should not be used as specifications. Molded plaques 0.080” thick were cured 20 hours at 100 ëC before testing
Caution: Contact with product dusts from regrinding operations may cause temporary irritation of the eyes and the respiratory tract. Use with local exhaust. Under hot melt processing conditions (170-230°C), wear personal protective equipment to prevent thermal burns.
First aid: Eyes-Flush eyes with flowing water at least 15 minutes. If irritation develops, consult a physician. Skin-Skin contact with hot melt may cause thermal burns. Call a physician immediately. Inhalation-If vapors generated from the hot melt process are inhaled, move to fresh air. Aid in breathing. If breathing difficulties develop, see a physician immediately. In
case of fire: Use water fog, foam, CO2, or dry chemical extinguishing media. Firefighters should be equipped with self-contained breathing apparatus and turnout gear.
Disposal: Waste material, unused contents and empty containers must be disposed of in accordance with applicable local, state or federal regulations. Refer to our Material Safety Data Sheet for specific disposal instructions.
In case of chemical emergency: Call CHEMTREC day or night for assistance and information concerning spilled material, fire, exposure and other chemical accidents. 800-424-9300 Attention: This product is sold solely for use by industrial institutions. Refer to our Material Safety Data Sheet regarding safety, usage, applications, hazards, procedures and disposal of this product. Consult your supervisor for additional information.